product:E-75-PB-EWP
The E-75 Series Video Entry phones are compact, weather and vandal resistant speaker phones designed to provide two-way handsfree audio communication and color composite video of who is at your door or gate. The E-75 also includes a built-in 125KHz HID compatible proximity card reader. The card reader outputs industry standard 26-bit Wiegand data, allowing it to be used with a Viking ES-1 door controller or any controller compatible with 26-bit Wiegand format. The E-75's compact size allows it to be mounted in a standard single gang electrical box. The E-75 is available in five different attractive finishes to match your door hardware, light fixtures, etc. Replacement E-75 faceplates (PNL75) can be purchased separately and are available in all five standard finishes. The E-75 entry phones can share a single phone line with house or small business telephones when used with a Viking model C-200, C-250 or C-2000B Entry Phone controller. The E-75 entry phones can also be connected to an unused analog station port (programmed for ring down) on a phone system or connected directly to a telephone line when used with a Viking model K-1900-5 auto dialer. The E-75 features a built-in high resolution color video camera, a built-in proximity card reader, microphone and speaker volume controls, selectable auto answer for monitoring and intelligent call progress detection for automatic hang-up when the call is completed. For outdoor environments or corrosive atmospheres, the E-75 is available with Enhanced Weather Protection (EWP), see DOD# 859.
Applications
Door or gate communication, business delivery entrances
Use with a Viking C-200 or C-250 to control one E-75 on a single phone line
Use with a Viking C-2000B to control 1 to 4 E-75s and door/gate control on a single phone line
Use with a Viking ES-1 for proximity card reader door control
Provide unique front and back door chimes and paging when used with a Viking SLP-1 or SLP-4 and C-2000B
Residential, commercial and industrial door security
Use with a Viking K-1900-5 or K-1900-30 for automatic speed dialing on telephone lines or analog PABX/KSU station ports
Use on any analog PABX station port with programmable ringdown capabilityFeatures
Built-in 125KHz HID compatible 26-bit Wiegand proximity card reader with LED and beep card read confirmation and EWP board protection
Built-in high resolution color video camera with wide viewing, tilt/swivel adjustments, and wide operating temperature of -30° F to 150° F
Mounting: Flush mounts in a double gang electrical box (2.25 deep x 3.65 wide x 2.84 tall minimum) or surface mounts in a Viking model VE-5x5 (not included, see DOD# 424) for mounting to a wall, post or VE-GNP Gooseneck Pedestal (EWP recommended)
Available in 5 standard faceplate finishes: Brushed Stainless Steel, Oil Rubbed Bronze, Polished Brass, Satin Black and Satin White
PNL-75 faceplates: Replacement faceplates with matching screws available in all five standard finishes
Vandal Resistant Features: 16 gauge polished brass or 18 gauge 304 stainless steel faceplate, 316 stainless steel push button, stainless steel speaker screen, scratch resistant powder coating, hex drive mounting screws
Weather Resistant Features: Mylar speaker, faceplate gasket, mic and speaker gasket, internally sealed (IP67) push button switch, self draining mic mount and UV stable weather resistant powder coating (excluding E-75-SS 304 Stainless Steel faceplate)
E-75-EWP is designed to meet IP66 Ingress Protection Rating (see DOD# 859 for more information)
Blue LED helps locate the push button, indicate ringing and off-hook
Programmable intelligent call progress detection for automatic hang-up on CPC, silence, busy signal, or time out
Specifications
Entry Phone Specifications
Power: Telephone line powered. Minimum 18V DC talk battery voltage with a minimum loop current of 20mA. Loop current may be boosted on low current lines with a Viking model TBB-1B Talk Battery Booster (see DOD# 632).
Dimensions: Faceplate: 123.8mm x 125.4mm x 4.3mm (4.875 x 4.938 x 0.17), Phone: 72mm x 46mm x 42mm (2.84 x 1.8 x 1.65)
Speaker Volume: Approximately 62db maximum @ 1m
Ring Voltage: 25V AC RMS minimum (for auto answer)
CPC Disconnect Time: 300ms minimum
REN: 0.8A
Camera Specifications
Power: 3.5-6V DC regulated 150mA (5V DC regulated adapter included)
Image Sensor: 1/4 color CMOS
Video Output: 1 VP-P composite, NTSC, 75 ohms
Resolution: 420 lines (640 x 480 @ 30fps / 307,200 pixels)
Sensitivity: 0.26 LUX (20 IRE) F 2.0
Lens: 3.4mm, pinhole 70° FOV (Field of View)
Tilt/Swivel Adjustment: Vertical +/- 20°, horizontal +/- 30° (see Diagram A)
IR Compatibility: This camera is equipped with an OLP (Optical Low Pass) filter to maintain correct video color in outside applications. The standard camera is NOT compatible with IR illuminators. If IR illumination is required, you will need to replace the exisiting camera with a Viking model VCAM-1IR, see DOD# 190.
Maximum Wire Run Length: 750 ft with *RG59/RG6 for video and CAT5 for power (3 pairs) and entry phone audio (1 pair). 150 ft with CAT5E for video, power and entry phone audio (longer video runs are possible by using video balun transceivers).
Entry Phone / Camera Specifications
Operating Temperature: -34° C to 65° C (-30° F to 150° F)
Humidity: Standard model: 5% to 95% non-condensing, EWP model: Up to 100%
Connections: (5) gel-filled butt connectors (3M Scotchlok UR2)
Shipping Weight: 0.55 kg (1.2 lbs)
Recommended Electrical Box for Flush Mounting: Double gang with minimum inside dimensions of 2.25 deep x 3.65 wide x 2.84 tall (Carlon BH234R or equivalent)
Recommended Surface Mount Box: Viking model VE-5x5 (DOD# 424) WARNING: Do NOT use a typical wet location box as not all styles seal properly with the E-75 faceplate.
Proximity Card Reader Specifications
Power: 5 to 14V DC @ 60mA maximum
Maximum Cable Length: 500 ft 24 Awg stranded shielded (Belden 9537)
Frequency: 125KHz
Format: 26 bit Wiegand
Read Range: 1.25 to 2.0
Credential Compatibility: HID - Proxcard II, ISOProx II and ProxTag II and Pyramid Series Cards and Tags (PSC-1, PSI-4, PSM-2 and PSK-3)
Transducer: Beeps during card read
LED: Red, turns off during card read
Humidity: Up to 100% (fully potted EWP)
Operating Temperature: -34° C to 65° C (-30° F to 150° F)